WorkSafeBC has rewritten the face seal rule for respirators in Part 8 of the Occupational Health and Safety Regulation (OHSR). The words "clean shaven" are gone. The rule now says the employer must not permit anything to interfere with the seal of a tight-fitting respirator. The Board of Directors approved the change in July 2026 and it takes effect on November 6, 2026.
The wording is new, but the standard a respirator has to meet is the same. Here is what changed, what did not, and what to update in your respiratory protection program.
The old rule and the new rule
Until November 6, 2026, section 8.39(2) read: "A worker required to wear a respirator which requires an effective seal with the face for proper functioning must be clean shaven where the respirator seals with the face."
Free Download: 5 Safe Work Procedures
Choose from 112 professionally written SWPs. No credit card required.
Get Free SWPsFrom November 6, 2026, section 8.39 reads:
- 8.39(1) defines a "tight-fitting respirator" as a respirator that requires an effective seal with the face for proper functioning.
- 8.39(2): "If a worker is required to wear a tight-fitting respirator, the employer must not permit anything to interfere with the seal or proper functioning of the respirator."
The old rule put the duty on the worker to be clean shaven. The new rule puts the duty on the employer, and it covers anything that interferes with the seal, not only facial hair. The new term "tight-fitting respirator" is also used in section 8.40 (fit tests) and section 8.41 (user seal check).
What did not change
WorkSafeBC's explanatory notes say the amendment "will not impact the current health and safety requirements" and only removes the specific reference to "clean shaven". The notes list the kinds of things that interfere with a seal and are still not allowed under a tight-fitting respirator: beards, sideburns and stubble, eyeglass temples, lip piercings and other jewellery, head coverings and cloth.
So a worker with a beard that crosses the sealing surface still cannot wear a tight-fitting half-face or full-face respirator. What changed is how the rule is worded and who carries the duty.
Loose-fitting respirators
Section 8.39 does not apply to loose-fitting respirators. The explanatory notes give powered air-purifying respirators with hoods or helmets as an example, and say they are already an acceptable class of respiratory protection when selected through a hazard and risk assessment. For a worker who cannot get a seal, a loose-fitting respirator that suits the hazard can be the answer.
Fit tests and seal checks still apply
Section 8.40 still says a tight-fitting respirator must not be issued to a worker unless a fit test shows the facepiece forms an effective seal with the wearer's face. A fit test is required:
- before initial use of a tight-fitting respirator;
- at least once a year;
- whenever the facepiece changes, including the brand, model and size;
- whenever changes to the user's physical condition could affect the fit.
Other personal protective equipment worn at the same time, and which could interfere with the fit, must be worn during the fit test. Under section 8.41, the worker still does a positive or negative pressure user seal check before each use, following CSA Standard CAN/CSA-Z94.4-18.
What to update before November 6, 2026
These are our suggestions:
- Rewrite the policy line. Replace "must be clean shaven" with wording that matches the new rule: nothing may come between the face and the seal of a tight-fitting respirator, including facial hair, stubble, jewellery and eyeglass temples.
- Make it an employer check. The supervisor confirms nothing interferes with the seal before work starts, instead of leaving it to the worker alone.
- Plan for workers who cannot get a seal. Decide in advance which loose-fitting respirators suit your hazards, so a worker is not sent home or left unprotected.
- Keep the fit test schedule. Annual testing and the re-test triggers are unchanged.
- Update your forms. Check pre-use checklists, PPE inspection forms and training slides for the old "clean shaven" wording.
For the full program, see our respiratory protection program guide. Our Silica Dust Control safe work procedure and PPE inspection checklist already use the new wording.
Keep respirator records in one place
Fit test dates, training and PPE inspections are easier to prove when they are all in one system. Make Safety Easy tracks certifications and expiry dates, PPE inspections and crew sign-off on any phone. Start a free trial to see how it works.
Sources: WorkSafeBC, approved amendments to Part 8 (Face seal, sections 8.39 to 8.41) with explanatory notes, July 2026; WorkSafeBC announcement of the Board of Directors' approval, July 30, 2026. In effect November 6, 2026. This article is general information, not legal advice.