0
General Safety

Lockout/Tagout (LOTO)

This procedure establishes requirements for the control of hazardous energy (lockout/tagout) during servicing and maintenance of machines and equipment.

Revision 2.1 Updated Jun 19, 2026

Scope and Purpose

This procedure sets out how to shut down, isolate, lock, tag and verify machines, equipment and circuits before anyone services, repairs, cleans, unjams, adjusts or maintains them, and how to return them to service safely.

Covers: every source of hazardous energy: electrical, mechanical (moving parts, flywheels, springs), hydraulic, pneumatic, chemical, thermal (steam, hot fluids), gravity (raised loads, booms, counterweights) and pressurized water, gas or steam lines. Applies to employees and contractors on our sites.

Hazard Identification

  • Unexpected start-up (another worker starts the machine, timer, remote or automatic control)
  • Electrical shock, electrocution, arc flash
  • Stored mechanical energy (springs, flywheels, coasting parts, raised booms, blades, counterweights)
  • Hydraulic and pneumatic pressure (injection, whipping hoses, sudden movement)
  • Steam, hot liquids, hot surfaces
  • Chemicals and process fluids in lines or vessels
  • Gravity (loads, buckets, hoppers, material that can fall or flow)
  • Re-accumulating energy (capacitors recharging, pressure creeping back through a leaking valve, heat)
  • Restart while removing locks (worker still in the machine, tools left in it)
  • Lock removed by someone else / bolt cutters
  • Tag-only isolation (device cannot take a lock)
  • Shift change or crew change gap
  • Contractor using a different lockout system

Required PPE

  • Hard hat.
  • Safety glasses; face shield where steam, hot fluid, chemical or pressure release is possible.
  • Safety footwear.
  • Work gloves suited to the task; chemical gloves per SDS where process fluids are present.
  • Electrical testing: voltage-rated insulating gloves with leather protectors, rated for the voltage being tested, and arc-rated clothing and face protection as set by the arc flash assessment for that equipment (see Arc Flash SWP). In Canada federal workplaces, work on equipment over 5,200 V between conductors or over 3,000 V to ground requires insulated protection equipment and tools and training in their use.
  • Hearing protection where noise requires it.

Key Procedure Steps

Set-up and shutdown

  1. Read the equipment-specific procedure.
  2. Tell affected workers that the equipment is being shut down and locked out, and why.
  3. Shut the equipment down with its normal controls, in the order the procedure or the manufacturer gives.

Isolate and lock

  1. Operate every energy isolating device to cut the equipment off from each source: open disconnects and breakers, close valves, insert blanks, disconnect linkages.
  2. Each authorized worker puts their own lock and tag on each isolating device, holding it in the off or safe position.
  3. Fill in the tag: name, date and time, reason.
  4. Where a lock cannot be fitted: attach the tag at the point the lock would go (or as close as safely possible, where anyone operating the device will see it), with an unreusable self-locking tie of at least 50 lb strength, AND add a second measure (remove the fuse or isolating element, open an extra disconnect, block the switch, remove the valve handle).

Release stored energy (after locks are on)

  1. Release or restrain all stored energy: discharge capacitors, ground where required, bleed hydraulic and air pressure through bleed valves, block or lower raised parts, release springs, drain lines, let hot parts cool.
  2. If energy can build back up, keep checking it (gauge, tester) until the work is done.

Verify zero energy

  1. Check that nobody is near the equipment or exposed.
  2. Try to start the equipment with its normal controls.
  3. Electrical: a qualified person tests each conductor and part the workers will be exposed to, phase to phase and phase to ground, including for backfeed and induced voltage.
  4. Read pressure gauges, temperatures and positions to confirm zero energy for every other source.
  5. Only now start the work.

During the work

  1. Workers joining the job put their own lock on the group box before they start; workers leaving take their lock off when they stop.
  2. Shift or crew change: the oncoming worker puts on their lock before the off-going worker takes theirs off, and they walk the isolation together.
  3. Testing or positioning that needs power: clear tools and materials, move everyone clear, remove locks (each person their own), energize and test, then shut down and repeat steps 3 to 14 before work continues.

Close-out and return to service

  1. Remove tools, parts, blocks and materials.
  2. Electrical: a qualified person confirms jumpers, shorts and temporary grounds are removed.
  3. Check that every worker is clear of the equipment.
  4. Put operating controls in off or neutral.
  5. Tell affected workers that locks are coming off and the equipment will be energized; warn them to stay clear.
  6. Each worker removes only their own lock and tag.
  7. Re-energize and check the equipment runs properly.
  8. Tell affected workers that the equipment is back in service.

Absent-worker lock removal (only if the person who applied the lock is not at the site)

  1. Never cut a lock to save time.
  2. A lock left by an absent worker may be removed only under the employer's written absent-worker procedure, and only by the authorized supervisor.
  3. Canada federal electrical isolation: there is NO absent-worker exception.

Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.

Training Requirements

  • Authorized worker: Training in recognizing the hazardous energy sources, the type and size of energy in our workplace, and how to isolate and control it; this procedure; the equipment-specific procedure for the machine.
  • Affected worker: Purpose and use of the procedure; never restart or remove locked or tagged equipment.
  • Other workers in the area: Told about the procedure and the ban on restarting locked or tagged equipment.
  • Qualified person (electrical testing): Trained on the equipment, the tester and live-dead-live testing.
  • Lead authorized worker / supervisor: All of the above, plus group lockout, shift hand-over, and the absent-worker removal procedure.
  • Person giving or receiving a guarantee of isolation (Canada federal): Authorized in writing by the employer.

Regulatory References

  • US OSHA 29 CFR 1910.147, The control of hazardous energy (lockout/tagout), incl. Appendix A (typical minimal lockout procedure, non-mandatory). General industry; excludes construction.
  • US OSHA 29 CFR 1910.333(b), Working on or near exposed deenergized parts (lockout and tagging of electrical circuits).
  • US OSHA 29 CFR 1926.417, Lockout and tagging of circuits (construction).
  • US OSHA 29 CFR 1926.702(j), Lockout/tagout procedures for concrete and masonry equipment (construction).
  • US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
  • Canada: COHSR SOR/86-304, s. 1.2 ("locked out"), Part VIII Electrical Safety (ss. 8.12 to 8.18 isolation and guarantees of isolation), Part XIII s. 13.16 (lockout for repair and maintenance of machines), Part XV (reporting). Federally regulated workplaces.
  • Provincial OHS regulations each have a lockout part. Use the one for your province.
  • Consensus standards (named for reference, not quoted): CSA Z460, Control of hazardous energy: Lockout and other methods; ANSI Z244.1, The control of hazardous energy: lockout, tagout and alternative methods. Confirm the current edition.

Download the Full PDF Template

Get the complete Lockout/Tagout (LOTO) document as a fillable PDF, part of the Safe Work Procedures Template Pack.

Get Template Pack

Get This SWP + 4 More Free

Choose from 112 procedures. No credit card, no commitment.

Pick Your 5 Free SWPs

Want Digital Sign-Off for Your SWPs?

Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.

Start Your Free Trial