Trench Box / Shield Installation
Trench box and shield installation, repositioning and removal procedures.
Scope and Purpose
This procedure covers selecting, inspecting, rigging, installing, using, moving, stacking and removing manufactured trench boxes (trench shields) used to protect workers from cave-ins.
A trench box does not stop the walls from caving in. It protects the workers inside it if they do. Workers are protected only while they are inside the box.
Hazard Identification
- Cave-in before the box is set
- Cave-in outside the box or at its open ends
- Box overloaded (too deep for the rating, surcharge, stacked beyond rating)
- Box shifts sideways when a wall fails
- Soil loss from under the box
- Caught between the box and the trench wall, or struck by the box during a move
- Dropped or swinging box during lifting
- Pinch and crush points when assembling spreaders or stacking
- Exposed while entering or leaving
- Falling objects into the box
- Water in the trench
- Hazardous atmosphere
- Damaged box (bent panels, cracked welds, bent spreaders)
Required PPE
- Hard hat.
- Safety footwear.
- Safety glasses.
- High-visibility vest or garment. Required in the US when exposed to public vehicle traffic; company floor: worn by everyone on site while boxes are being lifted or moved. Company floor: ANSI/ISEA 107 Class 2 or CSA Z96 Class 2 or higher.
- Work gloves suited to handling steel (rigging, pins, spreaders).
- Hearing protection where equipment noise requires it.
Key Procedure Steps
8.1 Select the box
- From the tabulated data, confirm the box (or stacked set) is rated for the full trench depth in the soil type the competent person recorded today.
- Confirm the inside width (spreader length) leaves room for the pipe or structure and the workers, and that the spreaders used are within the manufacturer's limits.
- Plan how much of the box height will be above grade.
- For depths beyond one box, stack only as the tabulated data allows, using the manufacturer's stacking hardware, or use a box made for the full depth.
- Inspect the box (checklist item 5) before it goes in the ground.
8.2 Assemble (at the surface)
- Assemble side panels and spreaders on firm, level ground away from the trench edge, following the manufacturer's instructions.
- Fit all pins and keepers.
8.3 Install
- Nobody is in the trench while the box is set.
- Rig to the manufacturer's lift points with rated slings and hardware.
- Dig only the length needed for the box.
- Lower the box under the direction of one signal person.
- Set the box level and plumb in the trench.
- For stacked boxes: set the bottom box, then the top box, and install the stacking pins or hardware before anyone enters.
- Install the ladder inside the box.
- The competent person inspects the installed box, the trench walls, the ends, and the edge, then authorizes entry.
8.4 Work inside the box
- Enter and leave only by the ladder inside the box.
- Work only inside the box.
- Do not dig more than 2 ft (0.61 m) below the bottom of the box, and only if the box is rated for the full depth of the trench and there is no sign of soil coming from behind or under the box.
- No loads over workers.
- Keep spoil and materials at least 1 m (3.3 ft) back from the edge (company floor).
8.5 Move the box
- Everyone out of the box and the trench section next to it before any move, lift or drag.
- Drag or lift the box using the manufacturer's pull or lift points only.
- Backfill the trench behind the box as it advances, so no unprotected trench is left open where workers could walk.
- Where the box cannot be dragged, set a second box ahead before removing the first, or lift and re-set it with everyone out.
- Re-block or re-backfill the gaps, re-inspect, and re-check the ladder before re-entry.
8.6 Remove
- Everyone, plus tools and materials, out of the box and trench.
- Backfill inside and around the box in stages as the box is raised, so the trench walls are not left unsupported.
- Lift the box straight up.
- Backfill the remaining trench immediately, or protect it as an open excavation under SWP-005.
- Clean and inspect the box.
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Competent person: Soil classification; reading the manufacturer's tabulated data (depth rating, stacking, spreader limits, dig-below limits); box inspection; authority to stop work.
- Qualified person (Canada federal): Knowledge, training and experience to install and remove the box or supervise it.
- Equipment operator: The machine; lifting with rigging; the box's lift and pull points; dragging and removal methods from the manufacturer.
- Rigger / signal person: Sling and hardware inspection; hand signals; keeping people clear of loads.
- Trench workers: This SWP and SWP-005: stay inside the box, ladder use, out during moves, signs of trouble.
Regulatory References
- US OSHA 29 CFR 1926.650 (definitions: shield, tabulated data, competent person).
- US OSHA 29 CFR 1926.651(c)(2) (egress), (j) (spoil setback), (k) (inspections).
- US OSHA 29 CFR 1926.652(a) (protection required), (c)(2) (manufacturer's tabulated data), (d) (materials and equipment), (g) (shield systems).
- US OSHA 29 CFR 1926 Subpart P Appendix A (soil classification) and Appendix B (shielded vertical lower portion, 18 in).
- US OSHA 29 CFR 1926.251 (rigging equipment) and 1926.1053(b)(1) (ladders).
- US OSHA 29 CFR 1926.21(b)(2) (training) and 1904.39 (reporting).
- Canada: COHSR SOR/86-304 Part III s. 3.12 (Excavation, incl. 3.12(4) steel plate and bracing systems), s. 3.11 (ladders), Part XV (reporting), for federally regulated workplaces.
- Provincial OHS regulations each have excavation and trenching requirements. Use the one for your province.
- Manufacturer's tabulated data, instructions and written approvals for the specific box in use.
Download the Full PDF Template
Get the complete Trench Box / Shield Installation document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial