Concrete / Demolition Saw
Concrete and demolition saw operation with mandatory silica dust controls.
What This Procedure Covers
- Identify the saw and approved cut
For trained operators cutting concrete, masonry or similar materials with an approved saw and blade. Handheld, floor and wall saws have different setup, guarding and operating requirements. Use the procedure for the actual model and task.
Confirm what is behind and within the cut: Identify embedded services, reinforcement and post-tensioning through the approved investigation process. Scanning alone is not authorization to sever an unknown object. Obtain the required structural or service approval and stop if the material differs from the plan.
- Support the work and control access
Plan for the cut section's weight and movement, including release at the final cut. Establish supports, lifting arrangements and exclusion areas before sawing. Protect people on both sides and below the cut.
Prevent trapping the blade or losing the cut section: Arrange support so the work cannot shift unexpectedly or close onto the blade. Do not rely on a generic twenty-five-foot boundary; account for the equipment, debris, falling sections and local requirements. Check wall-saw anchorage or floor-saw travel arrangements under the model-specific plan. Keep hoses and cables clear of the blade and travel route. Use suitable electrical protection for wet work and equipment rated for the conditions. Do not use petrol-engine saws in enclosed areas where exhaust can accumulate.
- Select the correct silica-control method
Record the actual saw task, indoor or outdoor setting and exposure duration. Use the applicable local exposure-control requirements. Where using US OSHA Table 1, implement the complete entry for the actual equipment and task.
A vacuum is not an automatic substitute for water: The OSHA Table 1 handheld-power-saw entry specifies integrated continuous water delivery; attaching a HEPA vacuum does not automatically satisfy that entry. An alternative method needs the applicable exposure-assessment approach. Other saw types have their own requirements. Stop if the specified dust control fails. Select respiratory protection from the actual task requirements and assessment. A P100 filter label alone does not define the protection factor of the complete respirator. Confirm training, fit testing where required and compatibility with other PPE before work.
- Inspect the saw and blade
Confirm the blade is approved for the material, saw, diameter, arbor, rotation and wet or dry method. Verify its speed rating is suitable for the saw. Remove damaged blades and equipment from service.
Use the manufacturer inspection and setup method: Inspect for cracks, missing segments, distortion and other damage. Install and check the blade under the saw instructions with the equipment made safe. Keep the required guard in position. Do not fit an unsuitable blade, bypass an interlock or use the side of a cutting blade for grinding. Select hearing protection through the noise assessment rather than a generic rating. Check that face, eye and respiratory protection work together. Plan breaks and task changes for vibration and fatigue; PPE does not replace the specified engineering controls.
- Cut under the approved operating method
Use the model-specific start, feed, depth and stopping instructions. Maintain stable footing and control of the machine. Keep everyone clear of the blade and foreseeable kickback or section-movement path.
Do not twist or force the blade: For handheld cutters, maintain the prescribed two-handed grip and avoid engagement of the upper blade quadrant that can cause kickback. Keep the cut aligned and do not apply sideways force. If the cut binds or the work moves, stop and make the saw safe before assessing the cause. Follow the saw's stopping sequence; do not improvise a universal withdrawal method for all machines. Keep people clear until movement stops. Collect slurry before it dries and use suitable wet or HEPA methods for cleanup rather than creating airborne silica dust.
- Secure and hand over
Leave cut openings and edges guarded, removed sections stable and the work area clear. Record defects and remaining structural, service or access restrictions before the next crew enters.
Reference guidance: OSHA silica construction guidance and handheld-power-saw fact sheet; Husqvarna power-cutter instructions as model-specific examples. Complete with local requirements and the actual saw and blade instructions.
Download the Full PDF Template
Get the complete Concrete / Demolition Saw document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial