0
Construction Specialty

Drywall Installation

Drywall installation safety covering material handling, stilts, cutting and dust control.

Rev 02 Updated Apr 19, 2026

What This Procedure Covers

  1. Work scope and responsibility

    For installation and finishing of identified gypsum-board products. Demolition, suspect asbestos-containing material and structural alteration need separate assessment and authorization.

    Plan the sequence: Coordinate delivery, storage, access, concealed services, installation and finishing before work starts. Identify other trades and occupied areas that could be affected by lifting, falling material or dust.

  2. Delivery, storage and handling

    Use the actual product weight and dimensions to plan handling. Sheet size alone does not determine a safe manual lift or the number of people required.

    Prevent collapse, strain and crush injuries: Use suitable carts, panel carriers and lifting equipment for the route and load. Store board according to supplier instructions on adequate support, away from access routes and unprotected edges. Restrain upright storage using a suitable rack; do not leave unsecured sheets leaning where they can fall. Keep hands and feet clear of pinch points while moving or lowering panels. Reassess the method if a panel cannot be controlled without twisting, overreaching or prolonged overhead holding.

  3. Access and overhead panel support

    Choose a stable platform and suitable panel lift for ceiling work. Follow the lift instructions for loading, panel retention, capacity and lowering; keep people clear of an unsecured panel.

    Stilts require a separate decision: Do not assume stilts are allowed for every installation task or location. Confirm applicable rules, site permission, manufacturer limits and worker competence. If permitted, restrict use to the approved task on a clear, level, dry surface, with protected openings and a planned mounting and dismounting point. A nominal setback is not a substitute for protecting an opening. Select scaffold and fall controls for the actual configuration and jurisdiction; do not use a universal height threshold from this template.

  4. Cut, position and fasten

    Prepare cuts on a stable support where possible. Control sharp edges and knife travel, keep the free hand clear, retract or guard the blade when not cutting, and use a suitable sharps container for discarded blades.

    Install to the specified assembly: Verify framing and concealed services before fastening. Use the specified fastener type, length, spacing and penetration for the assembly. Set the screw gun appropriately and check the first installed panel. Overdriven or missed fasteners need correction according to the installation specification. Keep panel support in place until the panel is adequately secured. Do not remove required protection or reach beyond safe platform access to position a sheet. Stop for unexpected movement, damaged framing or an unidentified service.

  5. Compound, sanding and dust controls

    Review each product SDS and the work method. Dust composition varies; determine exposure controls for the actual board and compound, including silica where present.

    Control dust at source: Use compatible vacuum-assisted sanding or an approved lower-dust method. Maintain the extraction system and filters as specified. Separate the work from other trades and occupied spaces. Stop and correct ineffective extraction rather than continuing in a visible dust cloud. Do not assume an N95 is sufficient for every exposure. Where respirators are required, implement the applicable selection, fit-testing, training and health-evaluation arrangements. Clean with a suitable filtered vacuum or approved wet method; avoid redistributing settled dust.

  6. Completion, local additions and follow-up

    Inspect the work area and installation before release. Remove loose scraps and sharps, secure remaining materials and report damage or unfinished work affecting others.

Reference guidance: NIOSH Preventing Injuries from Installing Drywall (2006-147); NIOSH drywall sanding evaluation (2019-0179-3365) and construction respirator guidance; WorkSafe Victoria Use of Plasterers' Stilts. Apply local rules and product/equipment instructions.

Download the Full PDF Template

Get the complete Drywall Installation document as a fillable PDF, part of the Safe Work Procedures Template Pack.

Get Template Pack

Get This SWP + 4 More Free

Choose from 112 procedures. No credit card, no commitment.

Pick Your 5 Free SWPs

Want Digital Sign-Off for Your SWPs?

Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.

Start Your Free Trial