0
Power Tools

Router Operation

Router operation including feed direction, speed selection and bit safety.

Rev 02 Updated Apr 19, 2026

What This Procedure Covers

  1. Scope and approval

    Identify whether the router is handheld or installed in an approved table. Complete the applicable setup page before use. CNC machines, spindle moulders and improvised inverted mounting are outside this procedure.

    Select the setup for the work: Identify the cutter-contact, ejection and kickback hazards. Reject work that cannot be supported or guided securely. A handheld feed-direction example must not be transferred to a router table without checking its actual cutting geometry.

  2. Tooling, speed and pre-use inspection

    Disconnect the energy source before installing cutters or making exposed adjustments. Inspect the collet, cutter, base, guards, switches and supply; remove defective equipment from use.

    Use the specified insertion and speed limits: Fit the cutter to the insertion depth and tightening method specified by the router and cutter manufacturers. Do not use a universal fraction of shank length or bottom the shank unless the instructions call for it. Set speed within the limits of the cutter, router and intended operation. Check the stock for embedded metal and defects. Keep hair and loose clothing away from the cutter and do not wear gloves where they could be caught. Plan dust collection and cleanup for the material being routed.

  3. Handheld configuration

    Complete this page for fixed-base or plunge handheld work. Secure the stock to a stable support and keep the cutter clear of clamps, bench surfaces and concealed services.

    Control the tool throughout the cut: Use both designated handles. Support the base with the cutter clear of the material before starting. Allow operating speed to develop before entering the cut. Use the approved plunge and depth-lock method for a plunge router; a fixed-base tool is not automatically suitable for plunge entry.

    Confirm the feed direction: Feed against cutter rotation at the contact point. For a conventional handheld router viewed from above, outside-edge routing normally proceeds counterclockwise and an inside opening clockwise. Confirm the actual cutter rotation and guide arrangement. Climb cutting is not authorized by this general procedure.

  4. Router-table configuration

    Complete this page only where the router and table are approved for use together. Follow both manuals for mounting, cutter limits, guarding and access to the stop control.

    Guide the stock without exposing hands: Use the specified fence, guard, holding aids and push devices for the operation. Support long stock without obstructing the feed. Small, narrow or curved work needs an appropriate jig or approved guiding method; do not attempt unsupported freehand feeding past an exposed cutter. Feed against rotation as shown by the table instructions and feed markings. On a conventional fence setup this is normally right to left from the operating position. Do not trap the work between the cutter and fence or assume every setup uses the same arrangement.

  5. Cut, stop and deal with faults

    Make controlled passes at the approved depth and feed rate. Do not force the cutter or continue if the stock chatters, the cutter burns or the tool pulls unexpectedly.

    Loss of control or abnormal operation: Stop using the accessible control while keeping clear of the cutter. Wait for all movement to stop and disconnect the energy source before clearing a jam or adjusting the setup. Investigate cutter condition, speed, support and feed direction before authorized restart.

    Keep control during rundown: Keep a handheld router securely supported and hands on the handles until rotation stops. Do not put down a router with the cutter turning. For a table, do not reach past the guard or remove trapped waste while the cutter is moving.

  6. Local instructions and verification

    Record the actual setup and any restrictions. Attach drawings where words alone do not clearly show support, guard placement or feed direction.

Reference guidance: CCOHS Powered Hand Tools - Routers and Woodworking Machines - General Safety Tips; Bosch 1617/1618 instructions 2610051825 (2018). Complete using the actual router, cutter and table manuals.

Download the Full PDF Template

Get the complete Router Operation document as a fillable PDF, part of the Safe Work Procedures Template Pack.

Get Template Pack

Get This SWP + 4 More Free

Choose from 112 procedures. No credit card, no commitment.

Pick Your 5 Free SWPs

Want Digital Sign-Off for Your SWPs?

Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.

Start Your Free Trial