Silica Dust Control
Respirable crystalline silica exposure control using OSHA Table 1 methods and engineering controls.
Scope and Purpose
This procedure sets out how to cut, drill, grind, chip, break, mix and clean up materials that contain crystalline silica without workers or others nearby breathing respirable silica dust.
Every cutting, drilling, grinding or chipping task on concrete, masonry, stone, tile, mortar or fibre cement uses a working dust control at the tool: water at the cutting point, or a shroud with a dust collector. If the water stops or the vacuum stops pulling, stop the tool.
Hazard Identification
- Breathing silica dust from saws (handheld, walk-behind, stationary, drivable)
- Breathing silica dust from drilling and core drilling
- Breathing silica dust from jackhammers and chipping tools
- Breathing silica dust from grinding and tuckpointing
- Breathing silica dust from floor grinding and milling
- Breathing silica dust from mixing dry cement, mortar or grout
- Dust from heavy equipment breaking, ripping, crushing or demolishing
- Clean-up making dust airborne again
- Dust reaching other trades, occupants or the public
- Control fails during work (water stops, hose kinks, shroud cracks, filter clogs, vacuum airflow drops)
- Wrong, damaged or poorly fitted respirator
- Take-home dust on clothing, skin and in vehicles
- Electric shock: water-fed tools with electric power
- Slips on wet floors and slurry
- Slurry reaching drains, ground or water (environmental)
- Flying particles and blade or wheel fragments
- Noise from saws, jackhammers and grinders
- Hidden asbestos or lead in the material
- Heat stress from respirators and coveralls
Required PPE
- Indoors or in enclosed areas: provide exhaust as needed so visible airborne dust does not build up.
- Wet methods: apply water at a flow rate high enough to minimize visible dust. Table 1 sets no flow number; use the tool maker's figure as the minimum.
- Enclosed cabs and booths: kept as free as practicable from settled dust; door seals, closing mechanisms, gaskets and seals working; positive pressure from a continuous fresh air supply; intake air filtered at 95% efficiency in the 0.3 to 10.0 micrometre range (for example MERV-16 or better); heating and cooling.
- Medical evaluation before the fit test and before required use (1910.134(e)(1)).
- Fit test with the same make, model, style and size before first use, whenever the facepiece changes, and at least annually (1910.134(f)(2)).
- User seal check every time a tight-fitting respirator is put on (1910.134(g)(1)(iii)).
- No facial hair between the face and the sealing surface or interfering with the valve (1910.134(g)(1)(i)(A)).
- Glasses and other PPE worn so they do not break the seal (1910.134(g)(1)(ii)).
- Respirators are the last line. They never replace a missing Table 1 tool control.
- Voluntary use (where not required): the worker gets the 1910.134 Appendix D information; other than filtering facepieces, the respirator still needs medical clearance and care under the program (1910.134(c)(2)).
- Eye protection with side protection for flying particles (US 1926.102(a)(2)); Canada federal: selected per CSA Z94.3 (COHSR 12.12). Face shield over glasses for grinding and chipping (company rule).
- Hearing protection selected from the noise assessment.
- Gloves for the tool and for wet cement (skin contact with wet cement products: SDS).
- Slip-resistant protective footwear (COHSR 12.11).
- Coveralls, disposable or washable, for heavy dust tasks (company rule). Never cleaned with compressed air.
- Hard hat where there is overhead work or falling material.
Key Procedure Steps
Plan
- List every task that will cut, drill, grind, chip, break, mix or clean up silica-containing material.
- Eliminate or substitute first: pre-cut or pre-cast pieces, sawing and lifting instead of breaking, pre-mixed products, a method that makes less dust.
- Check for asbestos and lead in the material before it is cut (Section 1).
- Match each task to its Table 1 row (Section 5).
- If a task is on Table 1 and every control in the row will be fully used, the Table 1 respirator applies and no exposure assessment is needed for that task (US (c)(1), (e)(3)).
- If a task is not on Table 1, or any part of the row will not be used, the alternative route applies (US (d)):
- Record the task, row or assessment, and respirator in the exposure control plan.
Set up
- Do the pre-work checklist (Section 7).
- Mark the work area and post warnings at access points.
- Connect the water and check it flows at the point of cut before the tool touches the material.
- Put on the respirator if required.
Work: saws
- Start the water before the cut and keep it running through the whole cut.
- Fibre-cement saws with a dust collector: outdoors only, blade 8 in or less.
- Walk-behind and handheld saws indoors or enclosed: APF 10 respirator for every duration.
Work: drills
- Fit the shroud to the bit size.
- Core drills: water to the cutting surface; collect the slurry as it comes out.
Work: jackhammers and chipping tools
- Use the water spray at the point of impact, or the shroud and collector.
Work: grinders
- Tuckpointing: shroud and collector at 25 cfm or more per inch of wheel diameter.
- Other grinding: water-fed grinder outdoors only, or shroud and collector.
- Floor grinders and walk-behind milling: water, or the maker's collector.
Work: mixing dry products
- Mix outdoors or with local extraction.
Work: heavy equipment and crushers
- Keep cab doors and windows closed while breaking, ripping, crushing or demolishing.
During the work
- Watch the dust.
- Empty or clean collector filters as the maker says.
- If a worker's total Table 1 time goes over 4 hours, change to the "more than 4 hours" respirator for every Table 1 task that shift.
- Keep other trades out of the dust.
Clean-up
- Collect slurry and wet dust before it dries.
- Bag collected dust and spent filters.
- HEPA-vacuum or wet-wipe tools, shrouds and hoses before they leave the work area.
End of shift
- HEPA-vacuum or wet-wipe clothing and boots before leaving the work area.
- Wash hands and face before eating, drinking, smoking or leaving the site (company rule).
- Clean and store the respirator per the maker; replace filters as the program says.
- Record each worker's Table 1 time and respirator use for the medical surveillance count (Section 10).
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Every worker covered by this SWP (US): Can show they understand: the health hazards of silica; the tasks at this site that make silica dust; the controls, work practices and respirators the employer uses; the content of 1926.1153; who the competent person is; the purpose of medical surveillance (1926.1153(i)(2)(i)).
- Every worker exposed or likely to be exposed (Canada federal): The employer's education and training program on silica: product identifier, SDS and label hazard information, other hazard information the employer knows, the qualified person's observations, safe handling and emergency procedures (COHSR 10.14(2)).
- Respirator users: Respirator training under the program, fit test and medical evaluation (1910.134).
- Tool operators: The tool maker's instructions for the dust control: water connection, flow check, shroud fit, vacuum hose, airflow indicator, filter cleaning and change.
- Competent person (US): Knowledge and ability to carry out the duties in 1926.1153(g): identify silica tasks, select and check Table 1 controls, recognize when an assessment is needed (1926.1153(b) definition).
- Qualified person (Canada federal): Knowledge, training and experience to carry out the hazard investigation and sampling (COHSR 1.2, 10.4).
Regulatory References
- US OSHA 29 CFR 1926.1153, Respirable crystalline silica (construction): (a) scope, (b) definitions, (c) Table 1 and conditions, (d) alternative exposure control methods, PEL and exposure assessment, (e) respiratory protection, (f) housekeeping, (g) written exposure control plan and competent person, (h) medical surveillance, (i) communication of hazards and training, (j) recordkeeping, Appendix A (lab methods).
- US OSHA 29 CFR 1910.1053, Respirable crystalline silica (general industry and maritime).
- US OSHA 29 CFR 1910.134, Respiratory protection (Table 1 assigned protection factors; medical evaluation; fit testing; seal check; training).
- US OSHA 29 CFR 1910.1020 (access to exposure and medical records); 1910.1200 (hazard communication, named); 1926.57 (ventilation, named for abrasive blasting); 1926.102 (eye and face protection).
- US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
- Canada: COHSR SOR/86-304, Part X ss. 10.4 to 10.9, 10.13 to 10.19, 10.21, 10.22; Part XII ss. 12.05, 12.11, 12.12, 12.13, 12.2; Part XV ss. 15.4, 15.5, 15.8; Part XIX ss. 19.5, 19.6 (federally regulated workplaces).
- ACGIH, Threshold Limit Values for Chemical Substances and Physical Agents (current edition). Named; the Canada federal limit.
- CSA Z94.4 (respirators), CSA Z94.3 (eye and face protectors). Named only.
- Related SWPs: Lockout / Tagout SWP-001; Confined Space SWP-002; Demolition SWP-009; Temporary Electrical Installations SWP-057; Pipe Laying in Trenches SWP-068; Asbestos Abatement SWP-076; Lead Paint Removal SWP-077; Spill Response and Cleanup SWP-081; Heat Stress Prevention SWP-084; First Aid Response SWP-090; CPR and AED Use SWP-091; Formwork and Falsework SWP-095; Work Over or Near Water SWP-109. Library task records: Concrete Saw, Core Drill, Hammer Drill, Angle Grinder, Masonry and Bricklaying, Noise Exposure Management.
- Provincial silica and exposure limit regulations and US state plans. Use the ones for your location.
Download the Full PDF Template
Get the complete Silica Dust Control document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial