Chainsaw Operation
Chainsaw operation including felling techniques, kickback prevention and PPE requirements.
What This Procedure Covers
- Define the task and competence
Use for chainsaw work planning and safe handling by trained operators. Tree felling, storm-damaged timber, climbing, aerial work and work near power lines require the appropriate specialist competence and separate approved task plans.
Do not extend the job beyond the assessed task: Identify what may move, fall, roll or spring when cut. Stop if timber condition or stored forces are uncertain. Do not treat familiarity with ordinary wood cutting as competence to fell a damaged tree, release a hung-up tree or cut storm-loaded timber.
- Assess the site and establish boundaries
Check terrain, footing, weather, overhead hazards, electrical lines, traffic and public access. Set boundaries for the actual task and foreseeable movement of timber, not merely the length of the guide bar.
Felling requires a separate competent plan: Where felling is authorized, the plan must address tree condition, fall direction, surrounding hazards and clear retreat routes. Normal retreat planning places routes diagonally to the rear, away from the intended fall direction; confirm the actual safe route with the competent faller. Do not use a generic hinge percentage as a cutting instruction. Stop for unsafe wind, poor visibility or an uncontrolled public boundary. Arrange assistance and communications suitable for the location. Only a qualified person (US 29 CFR 1910.399; Canada federal COHSR 1.2; see SWP-052) may assess and work near energized lines; a normal tree-work plan does not authorize line-clearance work.
- Inspect the saw and select protection
Check the model instructions before inspection, adjustment or starting. Remove defective equipment from service and keep incompatible bars, chains and replacement parts out of use.
Use the model-specific tension and test method: Check chain condition and tension as instructed by the manufacturer; a fixed quarter-inch pull is not a universal test. Verify the required safety controls and lubrication. Follow the prescribed method for making the saw safe before any adjustment, sharpening or obstruction removal. Select chainsaw protection suitable for the saw and task, and inspect it before use. Do not assume leg protection performs identically with every petrol, corded or battery saw. Follow its label and instructions, replace damaged protection and use safety eyewear beneath a mesh face screen.
- Start and cut within the approved method
Use the manufacturer-approved starting method, secure footing and a clear chain path. Never drop-start the saw. Keep other people outside the work boundary before starting and throughout cutting.
Maintain control of the saw and the workpiece: Use a firm two-handed grip and keep the body clear of the cutting path. Avoid contact between the upper bar tip and objects, and avoid pinching the chain. Do not overreach or cut above shoulder height. A chain brake and protective clothing do not eliminate kickback risk. Use stable ground-based access for the assessed task; do not improvise work from a ladder. Stop for unexpected timber movement, chain damage or a trapped saw. Make the equipment safe and obtain the appropriate competent assistance rather than pulling or cutting unpredictably loaded material.
- Refuel, transport and maintain safely
Apply the instructions for the actual petrol, corded or battery model. Keep fuel and electrical hazards included in the task assessment. Petrol-engine saws must not be operated in enclosed areas where exhaust can accumulate.
Control the power source during interruptions: Shut down and allow a petrol saw to cool before refuelling. Use approved fuel containers and keep ignition sources away. For battery or corded equipment, follow the manufacturer method to prevent unexpected starting during maintenance, clearing and transport. Stop the chain before moving between work positions and follow the instructions for carrying the saw. Cover the bar for transport and secure the equipment. Do not return a saw with defective safety controls to service until repaired and checked.
- Record and hand over
Leave timber stable and remaining hazards controlled. Record unfinished work, equipment defects and any specialist assessment needed before another crew continues.
Reference guidance: CCOHS Safe Use of Chain Saws and Kickback; WorkSafe NZ manual tree felling; STIHL protective apparel guidance. Complete using local requirements and the actual saw and PPE instructions.
Download the Full PDF Template
Get the complete Chainsaw Operation document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial