0
Environmental & Hazmat

Confined Space Entry

This procedure covers safe entry into permit-required confined spaces including tanks, vessels, silos, vaults, pits and other enclosed areas.

Revision 2.1 Updated Jun 19, 2026

Scope and Purpose

This procedure sets out how to enter, work in and leave a permit-required confined space safely, and how to get a worker out if something goes wrong.

Covers: entry into permit-required confined spaces (US) and hazardous confined spaces (Canada) such as tanks, vessels, silos, bins, hoppers, vaults, pits, manholes, sewers, lift stations, utility vaults and large ducts.

Hazard Identification

  • Oxygen deficiency (displaced by nitrogen, argon, CO2; used up by rusting, rotting material, combustion)
  • Oxygen enrichment (leaking oxygen cylinders or torch hoses)
  • Flammable gas, vapour or combustible dust (fuel, solvents, sewer gas, coatings, grain dust)
  • Toxic gas or vapour (H2S, CO from engines, welding fume, solvent vapour, chemical residue)
  • Engulfment (liquid, grain, sand, sludge, powder)
  • Moving parts and stored energy (agitators, mixers, augers, pumps, valves, hydraulic and pneumatic lines, electrical)
  • Internal shape that traps (converging walls, sloped floors, baffles)
  • Falling through the opening; objects falling in
  • Falls during climbing in or out
  • Traffic and equipment near the opening
  • Ventilation failure
  • Heat or cold inside the space
  • Noise (amplified inside metal spaces)
  • Poor lighting
  • Unplanned rescue attempt

Required PPE

  • Hard hat.
  • Safety glasses, or goggles / face shield where splash or dust is possible.
  • Gloves suited to the residue in the space (check the SDS).
  • Safety footwear; chemical-resistant boots where residue is present.
  • Full-body harness with the retrieval line attached at the centre of the back near shoulder level or above the head (wristlets or anklets only where the employer has shown a harness is infeasible or more hazardous).
  • Personal gas monitor worn by an entrant, in addition to the area monitor (site rule).
  • Hearing protection where noise requires it.
  • Respiratory protection as specified in the hazard assessment. Supplied air (SCBA, or airline with escape cylinder) is required for any entry or rescue where the atmosphere is unknown or cannot be kept within the acceptable entry conditions. Respirator users must be fit-tested and trained under the employer's respiratory protection program.
  • Flame-resistant clothing where the assessment identifies a flash fire risk.

Key Procedure Steps

Set-up

  1. Confirm the space is on the confined space list and read its hazard assessment.
  2. Coordinate with the host employer or controlling contractor and with any trade working nearby whose work could affect the space (welding, painting, pumping, traffic).
  3. Hold the pre-entry briefing at the space: hazards, signs and symptoms, acceptable entry conditions, alarm set points, communication method, evacuation signal, rescue plan.
  4. Set up barriers and traffic control around the opening.
  5. Remove any condition that makes it unsafe to open the cover (for example, pressure).
  6. Isolate the space: lock out energy, blank or blind lines, double block and bleed, disconnect linkages.
  7. Test the atmosphere from outside before changing the natural ventilation: oxygen first, then flammable gas, then toxic gas.
  8. Start forced-air ventilation from a clean air source, aimed at where people will work.
  9. Retest in the same order.
  10. Rig and inspect the retrieval system, harnesses and lines.
  11. Entry supervisor checks every item on the permit, confirms the rescue service is available and can be called, signs the permit and posts it at the opening.

Work

  1. Attendant takes position at the opening and starts the entry log (name, time in, time out).
  2. Entrant connects to the retrieval line and enters with a personal gas monitor.
  3. Monitor the atmosphere continuously while anyone is inside, with the monitor in the space.
  4. Attendant and entrant check in at the interval set on the permit.
  5. Everyone gets out immediately on: any gas alarm; an order from the attendant or supervisor; any symptom; any prohibited condition; ventilation failure; a hazard outside the space.
  6. After an evacuation, nobody re-enters until the supervisor has found the cause, fixed it, retested, and reissued or re-endorsed the permit.
  7. When the supervisor changes, the incoming supervisor confirms conditions still match the permit before work continues.

Close-out

  1. All entrants out.
  2. Remove tools and equipment.
  3. Remove isolation per the LOTO SWP.
  4. Supervisor cancels the permit and writes any problems on it.
  5. Debrief the host employer or controlling contractor on hazards found or created.

Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.

Training Requirements

  • Authorized entrant: Training in this procedure, the hazards of this space, signs and symptoms, equipment use, communication, evacuation signals.
  • Attendant: As entrant, plus counting and tracking entrants, recognizing behaviour effects, ordering evacuation, calling rescue, non-entry rescue with the retrieval system.
  • Entry supervisor: Full program, permit system, verifying tests and equipment, confirming rescue availability, ending entry.
  • Gas tester: Training on the specific monitor used: calibration, bump test, testing order, stratified spaces, recording.
  • Competent person (US construction) / qualified person (Canada): Knowledge, training and experience to identify spaces and assess hazards; appointed in writing by the employer.
  • Rescue service: Trained as an authorized entrant, plus assigned rescue duties and rescue PPE; basic first aid and CPR, with at least one member holding a current certificate available.

Regulatory References

  • US OSHA 29 CFR 1910.146, Permit-required confined spaces (general industry), incl. Appendix B (atmospheric testing, non-mandatory).
  • US OSHA 29 CFR 1926 Subpart AA, ss. 1926.1201 to 1926.1211, Confined Spaces in Construction.
  • US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
  • Canada: Canada Occupational Health and Safety Regulations (COHSR) SOR/86-304, Part XI Confined Spaces, and Part XV Hazardous Occurrence Investigation, Recording and Reporting (federally regulated workplaces).
  • Provincial OHS regulations each have a confined space part (for example BC, Alberta, Ontario). Use the one for your province.

Download the Full PDF Template

Get the complete Confined Space Entry document as a fillable PDF, part of the Safe Work Procedures Template Pack.

Get Template Pack

Get This SWP + 4 More Free

Choose from 112 procedures. No credit card, no commitment.

Pick Your 5 Free SWPs

Want Digital Sign-Off for Your SWPs?

Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.

Start Your Free Trial