Electrical Substation Work
Safe work practices for maintenance and repair within electrical substations.
Scope and Purpose
This procedure covers inspection, maintenance, testing, switching and repair work inside an electrical substation or switchyard. That includes yards, control buildings, switchgear rooms, cable vaults and trenches, transformers, breakers, disconnects, buses, capacitor banks and batteries.
It applies to company workers and contractors who enter the substation fence or a substation room.
Hazard Identification
- Electric shock or electrocution from contact with energized buses, conductors or terminals
- Approach too close (flashover through air) while reaching, climbing or carrying long objects
- Arc flash and arc blast during switching, racking breakers, testing, or opening covers
- Unexpected re-energization (backfeed, wrong switch, automatic or remote closing, other crews)
- Induced voltage from parallel energized circuits
- Stored energy in capacitors, cables, batteries and spring-charged breakers
- Step and touch potential during a fault, including at fences and grounds
- Draw-out breaker racking
- Insulating oil (fire, spills, skin contact) and SF6 gas and its arc by-products
- Enclosed spaces: cable vaults and trenches
- Mobile equipment (bucket trucks, cranes, boom trucks) inside the yard
- Slips, trips and falls on gravel, trenches, structures and equipment
- Heat, cold, lightning, wind and rain
Required PPE
- Arc-rated clothing, outer layer, covering the whole body
- Arc-rated face shield or hood, balaclava
- Hard hat, electrical class
- Safety glasses
- Rubber insulating gloves with leather protectors
- Rubber insulating sleeves
- Footwear
- Hearing protection
- Chemical PPE
Key Procedure Steps
Set-up
- Hold the job briefing (Checklist item 1).
- Report to the person in charge of the substation on entry (attended stations).
- Walk the work area.
- If the fence will be opened or extended, isolate, ground or bond the fence sections first (1910.269(u)(3)).
- Inspect and air-test rubber gloves; check sleeves and blankets; wipe and inspect live-line tools.
Isolation (de-energize)
- The employee in charge requests the clearance from the system operator.
- Open every switch, breaker, disconnect, jumper and tap that can feed the work, including backfeed sources.
- Tag automatic and remote controls that could close the opened devices at their control points, and disable them where the design allows (1910.269(m)(3)(iii)).
- Lock and tag every isolation point.
- For draw-out breakers: confirm the breaker is open before racking out, make the control circuit inoperable if the design allows, and rack out to the fully withdrawn position.
- Discharge capacitors and cables per manufacturer instructions and the label wait time.
Test and ground
- Prove the voltage detector on a known live source or proving unit.
- Treat non-current-carrying metal parts (transformer tanks, breaker housings) as energized at the highest voltage they are exposed to until you confirm they are grounded (1910.269(l)(11)).
- Install protective grounds so that the work position is in an equipotential zone:
- The employee in charge confirms steps 6-14 are complete and only then tells the crew the equipment may be worked as de-energized.
Work
- Keep MAD (Table 1) from every part that is still energized.
- Put on rubber gloves and sleeves before reaching into MAD, and take them off only after you are back out of reach of MAD (1910.269(l)(4)(ii)).
- Work from a position where a slip or shock will not throw you into contact with a part at a different potential.
- Do not open or close circuits under load unless the device is designed to interrupt or carry that current (1910.269(l)(12)).
- Fuses: when one or both terminals are energized above 300 V, use tools or gloves rated for the voltage.
- If grounds must come off for a test, everyone uses insulating equipment and is kept clear while the grounds are off (1910.269(n)(8)).
- Any switching that affects the work goes through the system operator or person in charge, with confirmation back before you act.
- If anything changes (new source found, unexpected voltage, weather, crew change), stop, re-brief and re-check isolation.
Close-out and re-energize
- Account for every worker.
- Remove protective grounds: line end first with a live-line tool, then the ground end (1910.269(n)(6)(ii); COHSR 8.22(2)(g)).
- Each worker removes only their own lock and tag.
- The employee in charge tells each worker the clearance is about to be released, confirms everyone is clear and all grounds are off, then reports to the system operator and releases the clearance (1910.269(m)(3)(x)).
- Re-energize only by the approved switching order.
- Watch and listen for abnormal conditions (noise, smell, heat, smoke).
- File the switching order, guarantee or clearance records and this checklist.
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Qualified worker: Training in all items of 1910.269(a)(2)(ii) for the voltages they will meet: recognizing live parts, determining voltage, MAD, PPE and insulated tools, hazard recognition.
- Employee in charge / person in charge: All qualified-worker training, plus the company switching, clearance and guarantee-of-isolation procedure.
- Safety watcher: Duties, hazards of this job, and emergency procedure (COHSR 8.8(2)).
- Unqualified worker: Site entry orientation: where live parts are, where they may go, what not to touch, the alarm and muster point.
- First aid and CPR: Enough trained people so that each worker exposed to shock can be reached by one within 4 minutes; at a remote substation where that is not possible, every worker on site is trained (1910.269(b)(1)(ii)).
- Rescue: Each worker trained in the rescue methods for the job, for example rescue from structures or vaults (1910.269(a)(2)(i)(B)).
Regulatory References
- 29 CFR 1910.269, Electric power generation, transmission and distribution: (a)(2), (a)(4), (b), (c), (j)(2), (l), Tables R-3, R-6, R-7, R-9, (m), (n), (p)(1), (u).
- 29 CFR 1910.137, Electrical protective equipment: (c)(2), Tables I-4 and I-5.
- 29 CFR 1910.303, General electrical requirements: (g)(2), (h).
- 29 CFR 1910.333, Selection and use of work practices: (c)(5) (enclosed spaces).
- 29 CFR 1926.950, Subpart V scope (construction of substations and T&D lines).
- Canada Occupational Health and Safety Regulations, SOR/86-304, Part VIII Electrical Safety: 8.4-8.22 and the Schedule; 12.11 (footwear).
Download the Full PDF Template
Get the complete Electrical Substation Work document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial