Ladder Jack Scaffolding
Ladder jack scaffold setup, load limits and fall protection requirements.
Scope and Purpose
This procedure covers setting up, using, moving and taking down ladder jack scaffolds for light work such as siding, painting, caulking, trim, gutters and window work, so that the ladders stay put, the platform carries its load, and nobody falls from it or is hit by anything falling from it.
Covers: ladder jack scaffolds made of two extension or single ladders, a pair of ladder jacks (inside or outside mount) and a platform of scaffold-grade planks or a manufactured platform.
Hazard Identification
- Fall from the platform
- Fall while getting on or off the platform
- Ladder slides, kicks out or tips sideways
- Ladder, jack or rung failure (overload)
- Platform breaks, slides or tips
- Falling tools and materials
- Power line contact (metal ladders, long tools, siding, gutters)
- Weather: wind, rain, snow, ice, lightning
- Raising the working height on the platform
- Being struck by vehicles or people
- Hanging in a harness after a fall
- Strains and pinch points when setting jacks and planks
Required PPE
- Full-body harness with an SRL (preferred at these heights) or an energy-absorbing lanyard only where the clearance chart allows; locking connectors; anchorage connector suited to the anchor. Body belts are not allowed for fall arrest.
- Hard hat. US: meets 1926.100. Canada federal: CSA Z94.1 or ANSI Z89.1 (COHSR 12.1).
- Safety glasses with side protection where there are flying particles (US 1926.102(a)(2)); Canada federal CSA Z94.3 (COHSR 12.12).
- Safety footwear with slip-resistant soles (Canada federal CSA Z195, COHSR 12.11).
- Gloves suited to the task.
- High-visibility apparel where vehicles or equipment move nearby (Canada federal CSA Z96, COHSR 12.17).
- Tool lanyards when working over people or public areas (site rule).
- Task PPE (respirator, face shield) for the work done from the platform (painting, sanding, cutting).
Key Procedure Steps
Plan
- Confirm the work suits a ladder jack scaffold (Section 1).
- Pick the anchorage: a roof anchor, structural member or engineered anchor above the work, independent of the ladders and platform, rated 5,000 lb (22.2 kN) per worker or designed, installed and used under a qualified person's supervision as part of a complete personal fall arrest system with a safety factor of at least two (US 1926.502(d)(15)).
- Work out clearance for the platform height using the SRL or lanyard maker's chart: free fall, deceleration distance, harness stretch, the worker's height below the D-ring and a safety margin (SWP-004).
- Canada federal: record the set-up in the fall-protection plan and plan the guardrail kit.
- Write or confirm the rescue plan (SWP-089).
Set up
- Barricade the area.
- Fit the jacks on the ladders as the manufacturer shows, at the same rung on both ladders, locking pins in.
- Raise each ladder with two people.
- Tie each ladder at the top to the structure (or fit stabilizers) and secure the feet where they could slide.
- Place the platform on the jacks: span within the limit, ends 6 to 12 in past the jacks or cleated, end stops on.
- Canada federal: fit the guardrails and toe boards on every open edge.
- Raise the jacks to working height only as the manufacturer allows, never above the fourth rung from the top (company rule) and never above 20 ft (6.1 m).
- Competent person inspects before first use.
Use
- Put on the harness, inspect it and the SRL, and connect to the anchorage before stepping onto the platform.
- Climb facing the ladder with three points of contact.
- Keep within the load: one worker per span unless rated for two; tools and light materials only.
- Do not lean out beyond the ladder rails, stand on the jack, or use boxes, buckets or ladders on the platform.
- Stop work for storm, lightning, wind at the company limit, snow or ice.
Move and take down
- Get off and remove all tools and materials before moving anything.
- Lower the jacks and platform in reverse order.
- Inspect components.
- If the scaffold is left unattended at the end of the day, take it down or remove the platform and secure the ladders (company rule).
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Scaffold user: Training by a person qualified in the subject: electrical, fall and falling-object hazards in the work area; how to deal with electrical hazards and use the fall and falling-object protection; proper use of the scaffold and handling of materials on it; the maximum intended load and capacity (US 1926.454(a)).
- Worker who sets up, moves or takes down the scaffold, and the inspector: As user, plus training by a competent person in: ladder jack hazards; the correct procedures for erecting, dismantling, moving, inspecting and maintaining this type of scaffold; design criteria, maximum intended load and intended use (US 1926.454(b)).
- Competent person (US) / qualified person (Canada federal): Knowledge, training and experience in ladder jack set-up, inspection and the manufacturer's instructions for the jacks, ladders and platforms used; appointed by the employer.
- Rescue person: Trained on the rescue method and equipment in the plan (SWP-089); first aid and CPR.
Regulatory References
- US OSHA 29 CFR 1926 Subpart L: 1926.450 (definitions), 1926.451 ((a) capacity, (b) platforms, (f) use incl. (f)(6) power lines, (g)(1)(i) PFAS on ladder jack scaffolds, (h) falling objects), 1926.452(k) (ladder jack scaffolds), 1926.454 (training); Appendix A to Subpart L (non-mandatory: ladder jack 25 lb/ft2, two employees, 8 ft span).
- US OSHA 29 CFR 1926 Subpart X: 1926.1053 (ladders), 1926.1060 (training).
- US OSHA 29 CFR 1926.502(d) (personal fall arrest systems), 1926.503 (fall protection training).
- US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
- Canada: COHSR SOR/86-304, Part II ss. 2.12, 2.13 (guardrails, toe boards), Part III ss. 3.1 to 3.11, 3.13, 3.14 (temporary structures, scaffolds, portable ladders, nets, housekeeping), Part XII ss. 12.06, 12.07, 12.09, 12.2, 12.21 (fall protection, training, records), Part XV (reporting), Part XIX s. 19.6 (training) (federally regulated workplaces).
- ANSI A10.8, CSA S269.2 (scaffolds); ANSI A14 and CSA Z11 (portable ladders; COHSR 3.11 names CAN3-Z11-M81); CSA Z259 series. Named only; check the edition your jurisdiction requires.
- Provincial OHS regulations. Use the one for your province.
Download the Full PDF Template
Get the complete Ladder Jack Scaffolding document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial