0
Fall Protection

Rescue from Heights

Rescue procedures for workers suspended in fall arrest systems with suspension trauma prevention.

Revision 2.1 Updated Apr 19, 2026

Scope and Purpose

This procedure sets out the rescue plan for a worker whose fall has been stopped by a personal fall arrest system and who is left hanging, or who is stranded at height (for example on a boom lift, platform or structure). It covers what must be in place before work at height starts, how to get the worker down quickly, and what to do after.

Rule: no one works on fall arrest unless a rescue plan for that work area is in place, the rescue equipment is at the work area, and the people who will carry it out are on site and trained.

Hazard Identification

  • Delayed rescue of a hanging worker (suspension intolerance)
  • Hitting the level below during the fall
  • Rescuer falls
  • Anchorage or rescue system overload (two people on one system)
  • Equipment failure during rescue
  • Injuries from the fall (head, spine, swinging into structure)
  • Rescue near energized lines, moving equipment, traffic
  • Weather, darkness, height of the building beyond reach of on-site equipment
  • Rescuer stress and fatigue

Required PPE

  • Full-body harness (body belts are not allowed for fall arrest), with the fall arrest attachment at the center of the back near shoulder level (or above the head where the rule allows).
  • Suspension relief straps on the harness (site rule).
  • Shock-absorbing lanyard or self-retracting lifeline, locking snaphooks and carabiners.
  • Self-rescue descent device where the plan uses self-rescue.
  • Hard hat with chin strap (site rule).
  • Their own fall protection, attached to a separate anchorage.
  • Rescue / descent device and rescue kit named in the plan, rated by the manufacturer for the rescue load.
  • Gloves suited to rope handling.
  • Eye protection.
  • Rescue knife or trauma shears, used only by trained rescuers and only as the plan directs.

Key Procedure Steps

Before work (planning)

  1. For each work area, pick the rescue method in this order of preference: (a) self-rescue the worker can do even if hurt; (b) assisted rescue from a platform, aerial lift or ladder; (c) assisted rescue with a pre-rigged raise/lower system; (d) professional rescue service as back-up.
  2. Write the plan: method, equipment and where it is kept, rescuers by name, anchorages for rescuers, how to call EMS, the access route for responders, and the clearance below each work area.
  3. Choose the worker's anchorage and lanyard so the worker cannot hit a lower level and can be reached by the planned method.
  4. Stage the equipment.

When a fall happens

  1. Shout for help.
  2. Talk to the fallen worker.
  3. If the worker can self-rescue safely, guide them to do it.
  4. Otherwise start assisted rescue at once with the planned method.
  5. Attach the rescue system to the worker's harness as trained (rescue attachment point or the fall arrest attachment), take the load off the worker's lanyard, release or cut it free only as the plan and the device instructions allow, and lower or raise the worker under control to a safe surface.
  6. If the planned method fails or cannot reach, use the back-up method in the plan.
  7. When a professional rescue team arrives, brief them and follow their direction.

After the worker is down

  1. Give first aid.
  2. Every worker who hung in a harness is checked by medical personnel, even if they feel fine (site rule).
  3. Remove all equipment involved in the fall and rescue from service.
  4. Investigate the cause.
  5. Report as required (section 9).

Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.

Training Requirements

  • All workers at height: Fall protection training (hazards, the systems used, inspection, the rules for your jurisdiction) by a competent person (US) / qualified person (Canada).
  • Trained rescuer: All of the above, plus hands-on training on the exact rescue equipment and methods in the plan for each work area.
  • Supervisor: All of the above, plus writing the rescue plan, confirming readiness, leading the rescue, calling EMS, preserving equipment, reporting.
  • First aider: First aid and CPR certificate to the level required by your jurisdiction and site.
  • Professional rescue service (if part of the plan): High-angle rescue capability confirmed for this site.

Regulatory References

  • US OSHA 29 CFR 1926.502(d), Personal fall arrest systems, incl. (d)(16) arrest criteria, (d)(19) impact-loaded equipment, (d)(20) prompt rescue, (d)(21) inspection; 1926.503 Training; Appendix C to Subpart M (non-mandatory), rescue considerations.
  • US OSHA 29 CFR 1910.140(c), Personal fall protection systems (general industry), incl. (c)(21) prompt rescue.
  • US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
  • Canada: Canada Occupational Health and Safety Regulations (COHSR) SOR/86-304, Part XII (fall-protection plan incl. rescue procedures s. 12.06; equipment s. 12.09; training s. 12.2; records s. 12.21) and Part XV (hazardous occurrence reporting), for federally regulated workplaces.
  • CSA Z259 series incl. Z259.2.3 Descent devices, as named in COHSR 12.09.
  • ANSI/ASSP Z359 Fall Protection Code, incl. Z359.4 (assisted-rescue and self-rescue systems). Named only.
  • Provincial OHS regulations each have fall protection and rescue rules. Use the one for your province.

Download the Full PDF Template

Get the complete Rescue from Heights document as a fillable PDF, part of the Safe Work Procedures Template Pack.

Get Template Pack

Get This SWP + 4 More Free

Choose from 112 procedures. No credit card, no commitment.

Pick Your 5 Free SWPs

Want Digital Sign-Off for Your SWPs?

Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.

Start Your Free Trial