Pile Driver Operation
Pile driving equipment operation with extreme noise controls, vibration monitoring and crane safety.
Scope and Purpose
This procedure covers driving and extracting piles with drop, diesel, air/steam, hydraulic impact and vibratory hammers, whether the hammer is mounted on a dedicated pile driver or hung from a crane: rig set-up, pile handling, driving, splicing and cut-off support, and shutdown.
Covers: steel H-piles, pipe piles, sheet piles, timber piles and precast concrete piles, on land or from barges.
Hazard Identification
- Hammer drops or runs up into the head block
- Pile swings, falls or slips while being hoisted into the leads
- Material falling onto the operator
- Rig or crane tips over (soft ground, batter leads, wind, overload)
- Power line contact by leads, boom, hammer line or pile
- Struck or crushed by the rotating superstructure
- Hose whip or line thrashing (steam, air, hydraulic)
- Flying debris (cap or cushion breaking, timber splintering, concrete spalling)
- Noise (impact hammers)
- Ground vibration damaging nearby structures or utilities
- Falls from the leads or loft platform
- Cave-in of pile pits or excavations
- Falling material when tube piles are blown out
- Cutting pile tops while driving continues
- Pinch and crush (pile into helmet, hands near leads, hammer trip)
- Fire and fumes (diesel hammer, fuel, hydraulic fluid)
- Drowning (barge or water work)
Required PPE
- Hard hat. US: meets ANSI Z89.1 (1926.100). Canada federal: CSA Z94.1 or ANSI Z89.1 (COHSR 12.1).
- Safety glasses with side shields (US 1926.102(a)(2); Canada federal CSA Z94.3, COHSR 12.12). Face shield over glasses where the crew must work close to the pile head during driving (company rule).
- Safety footwear with toe protection (Canada federal CSA Z195, COHSR 12.11). Slip-resistant where footing is wet or muddy.
- High-visibility apparel where vehicles or equipment move (Canada federal CSA Z96, COHSR 12.17).
- Hearing protection selected from the noise survey. Company rule: earplugs plus earmuffs for everyone inside the driving zone during impact driving. Earplugs fitted individually (US 1926.101(b)); plain cotton is not hearing protection (US 1926.101(c)). Canada federal: CSA Z94.2 where COHSR 7.7 applies.
- Work gloves for handling piles, cables and rigging.
- Loft worker: full-body harness and lanyard tied to the lead attachment points. Body belts are not allowed for fall arrest (US 1926.502(d)).
- Over or beside water: life jacket or PFD (SWP-109).
Key Procedure Steps
Set-up
- Read the pile driving plan and the vibration monitoring plan.
- Check for overhead power lines.
- Set the rig on firm, level ground or mats.
- Assemble leads and hammer per the manufacturer.
- Inspect the rig (Section 10).
- Set the driving zone with barricades and signs: company floor at least 25 ft (7.6 m) from the pile being driven, extended to cover the swing radius of the rig and the full area the leads, hammer or pile could land in if they fell.
- Barricade the swing radius of the rotating superstructure (US 1926.1424(a)).
- Agree the signals.
- Brief the crew: plan, zone, signals, hearing protection, stop-work triggers, rescue plan.
Handling and pitching piles
- Rig the pile at its pick points with rated rigging (Crane Rigging SWP-006).
- Everyone stands clear while the pile is hoisted into the leads (US 1926.603(c)(2)).
- Set the pile in the helmet and on the ground.
Driving
- Start at low energy and increase as resistance builds, per the plan.
- The operator takes signals only from the designated signal person (US 1926.603(c)(1)).
- Nobody goes under the hammer unless the blocking device is in the leads under the hammer (US 1926.603(a)(5)).
- Loft worker climbs only by the lead ladder and stays tied off.
- Keep the driving log: blow count, energy, depth, alignment.
- Stop driving if the pile suddenly loses resistance, drifts out of line, or shows damage (mushrooming, cracking, buckling, splitting), if the cap or cushion fails, or if vibration readings reach the engineer's stop value.
- Blowing out steel tube piles: keep everyone well beyond the range of falling material (US 1926.603(c)(4)).
- Cutting pile tops: stop driving, unless the cutting is at least twice the length of the longest pile away from the driver (US 1926.603(c)(5)).
- Splicing: hammer lowered and blocked, or rig stopped, before workers splice at the pile head.
- Jacked piles: access pits have ladders and bulkheaded curbs (US 1926.603(c)(6)).
Work on the hammer or leads
- Before hands-on work on the hammer, cushion or leads: lower the hammer to the ground or block it, shut down and lock out per Lockout / Tagout SWP-001, and relieve steam, air or hydraulic pressure.
Shutdown
- Lower the hammer to the bottom of the leads or to the ground, or set it on the blocking device.
- Secure the leads and boom per the manufacturer's parking instructions.
- Inspect hammer, helmet and cushion.
- Complete the driving log and report problems to the next shift.
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Operator, dedicated pile driver or crane with pile driving attachment: US: trained, certified/licensed and evaluated under 1926.1427 (dedicated pile drivers are not exempt); an uncertified operator runs the rig only as an operator-in-training under a trainer.
- Signal person: US: qualified (third-party or employer's qualified evaluator), documentation on site listing each signal type (1926.1428(a)).
- Qualified rigger: Qualified person status in rigging (US 1926.1401).
- Competent person (rig and pit inspection): Designated by the employer; knows this rig, Subpart CC inspection items and excavation hazards.
- Loft worker: Fall protection training for the system used (Fall Protection SWP-004).
- A/D director (assembling or taking down leads and attachments, US): Competent and qualified person, or competent person assisted by qualified persons; knows the manufacturer's assembly procedure (1926.1404(a)-(c)).
- All pile crew: Briefed on this SWP, the pile driving plan, driving zone, swing radius, signals, hearing protection and stop-work triggers.
Regulatory References
- 29 CFR 1926.603, Pile driving equipment.
- 29 CFR 1926 Subpart CC, Cranes and Derricks in Construction, incl. 1926.1400 (scope, incl. dedicated pile drivers and pile driving attachments), 1926.1401, 1926.1404, 1926.1408 and 1926.1409 (power lines), 1926.1412 (inspections), 1926.1417 (operation), 1926.1419 (signals), 1926.1424 (work area control), 1926.1425 (keeping clear of the load), 1926.1427 (operator certification), 1926.1428 (signal person), 1926.1439 (dedicated pile drivers).
- 29 CFR 1926.52 and 1926.101 (noise, hearing protection); 1926.100, 1926.102 (head, eye protection); 1926.502 (fall arrest).
- 29 CFR 1926.605 (barges); 1926.651 and 1926.652 (excavations).
- 29 CFR 1904.39 (reporting).
- COHSR SOR/86-304: Part III (s. 3.12 excavations), Part VII (sound levels), Part XII (PPE, fall protection 12.07), Part XIV (materials handling: 14.4, 14.20, 14.21, 14.23 to 14.27, 14.29, 14.38, 14.39), Part XV (hazardous occurrence reporting), Part XIX (hazard prevention, training).
- CSA Z150 (mobile cranes, named by COHSR 14.21).
- Provincially regulated work: follow your province's OHS regulation for pile driving, cranes, operator certification and noise.
Download the Full PDF Template
Get the complete Pile Driver Operation document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial