Safety Net Installation
Safety net installation, drop testing, inspection and maintenance procedures.
Scope and Purpose
This procedure covers selecting, installing, testing, inspecting, using, moving and removing personnel safety nets used as fall protection in construction, and debris nets used to catch falling tools and materials.
Covers: horizontal personnel nets under bridges, steel and concrete frames, roofs and decks; nets with a debris liner; debris nets and catch nets on scaffolds and temporary structures.
Hazard Identification
- Fall while installing, moving or removing the net
- Net too far below the work, too small, or too low
- Net or support failure
- Falling through the mesh or a gap
- Injury from hitting debris or the structure in the net
- Damaged or aged net (cuts, UV, chemicals, heat, abrasion)
- Sparks, slag or heat from hot work above the net
- Tools and materials falling through to people below
- Worker caught in the net cannot get out
- Power lines near the net or supports
- Water below the net
Required PPE
- Full-body harness, SRL or energy-absorbing lanyard, locking connectors, anchorage connector (installers, and anyone working at an unprotected edge before the net is tested).
- Hard hat. US: meets 1926.100. Canada federal: CSA Z94.1 or ANSI Z89.1 (COHSR 12.1). Chin strap at height (site rule).
- Safety glasses (US 1926.102(a)(2); Canada federal CSA Z94.3, COHSR 12.12).
- Safety footwear with slip-resistant soles (Canada federal CSA Z195, COHSR 12.11).
- Work gloves for rope and hardware.
- High-visibility apparel where vehicles or equipment move (Canada federal CSA Z96, COHSR 12.17).
- Over water: life jacket or PFD (SWP-109).
Key Procedure Steps
Plan
- Decide where nets are used and confirm guardrails, covers, restraint and PFAS have been considered first (SWP-004).
- Get the layout from the net manufacturer or a qualified person: support points and spacing, sag, the net height below each work surface, outward extension and clearance below.
- Check the structure can take the support loads (qualified person).
- Plan installer fall protection and rescue.
Install
- Install support hardware at the spacing on the layout.
- Hang the net as close as practicable under the work surface, never more than 30 ft (9.1 m) below it, with this outward extension past the outermost edge of the work surface:
- Deploy the net with tag lines.
- Fasten the border rope at every support point.
- Close every gap between the net edge and the structure to 6 in (15 cm) or less (company floor).
- Set the sag to the manufacturer's instructions or the qualified person's layout.
- On bridges, keep the fall area between the work surface and the net clear.
Test
- Drop test after first installation and before anyone relies on the net: a 400 lb (180 kg) sand bag, 30 in plus or minus 2 in (76 cm plus or minus 5 cm) in diameter, dropped into the net from the highest walking/working surface where workers are exposed, and from not less than 42 in (1.1 m) above that surface.
- The net passes if it catches and holds the bag and the bag does not contact any surface or structure below.
- Certification in place of a drop test is used only when a drop test is unreasonable and a qualified person signs the certification (company rule; the law allows the employer or a designated competent person).
- Re-test (or re-certify): when the net is moved, after any repair or modification (company rule; the law says major repair), and every 6 months if it stays in one place.
Use
- Workers above work as normal with the net below.
- Remove materials, scrap, equipment and tools from the net as soon as possible and at least before the next shift.
- No hot work above the net without fire-resistant protection and the competent person's approval.
- Never use the net as a platform, walkway or storage, and never jump into it.
Remove
- Clear the net.
- Inspect, clean, dry and store the net out of sunlight, away from chemicals and heat, per the manufacturer.
Each step is shortened to its first sentence. The full procedure, with every condition, checklist and sign-off field, is in the PDF.
Training Requirements
- Net installer: Training by a competent person in: fall hazards in the work area; the correct procedures for erecting, maintaining, taking down and inspecting the nets; use and operation of safety nets and the PFAS used while installing (US 1926.503(a)); the manufacturer's instructions; the drop test.
- Competent person: As installer, plus net layout checks, drop test, weekly inspection and removal from service.
- Qualified person (net layout, clearance, certification): Recognized degree, certificate or professional standing, or extensive knowledge, training and experience in net systems and their design.
- Workers above the net: Briefing on what the net does and does not do, reporting damage and debris, never using the net as a platform (US 1926.503(a)(2)(iii)).
- Rescue person: Trained on the plan to get a worker out of the net and on installer rescue (SWP-089); first aid and CPR.
Regulatory References
- US OSHA 29 CFR 1926 Subpart M: 1926.500 (scope incl. (a)(2)(v)), 1926.501 (duty), 1926.502(c) (safety net systems), 1926.502(d) (PFAS for installers), 1926.503 (training).
- US OSHA 29 CFR 1926.105 (safety nets for tank and communication tower erection only).
- US OSHA 29 CFR 1904.39, Reporting fatalities, hospitalizations, amputations and losses of an eye.
- Canada: COHSR SOR/86-304, Part III s. 3.13 (safety nets on temporary structures, ANSI A10.11-1979), Part XII ss. 12.01, 12.05 to 12.09, 12.15, 12.19, 12.2, 12.21 (fall protection, drowning, defective equipment, training, records), Part XV (reporting), Part XIX s. 19.6 (training) (federally regulated workplaces).
- ANSI A10.11 (personnel and debris nets); CSA Z259 series (PFAS). Named only; check the edition your jurisdiction requires.
- Provincial OHS regulations. Use the one for your province.
Download the Full PDF Template
Get the complete Safety Net Installation document as a fillable PDF, part of the Safe Work Procedures Template Pack.
Get This SWP + 4 More Free
Choose from 112 procedures. No credit card, no commitment.
Pick Your 5 Free SWPsWant Digital Sign-Off for Your SWPs?
Make Safety Easy lets your crew acknowledge procedures on any device. Track who read what, when. No more lost paper forms.
Start Your Free Trial